PART 8: BUILDING SERVICES
Chapter 1: Electrical and Electronic Engineering Services for Buildings1.1 Introduction
1.1.1 Aim of this section of Codes of Electrical and Electronic Engineering Installations in Buildings
1.1.2 Guiding Sources of the Codes of Electrical and Electronic Engineering Installations
1.1.3 Designing an Electrical and Electronic Engineering Installations in Buildings and related structures
1.2 Lighting and Illumination
1.2.1 Determination of Illumination Levels for Different Application (Principle of Lighting )
1.2.2 Planning the Brightness Pattern
1.2.3 Lighting Calculations
1.2.4 Recommended Illumination Values
1.2.5 Artificial Lighting to Supplement Daylight
1.2.6 Selection of Appropriate Light Fittings
1.2.7 Illumination of Exit Signs and Means of Escape
1.2.8 Selection of Appropriate Type of Lamp
1.3 Electrical and Electronic Installations in Buildings
1.3.1 Aim of the Codes of this Section
1.3.2 Scope
1.3.3 Voltage Ratings
1.3.4 Exclusion from Scope
1.3.5 Terminology and Definitions
1.3.6 List of Symbols used for Electrical Drawings
1.3.7 Estimating the load of a building/ a complex
1.3.8 Fittings, Fixtures and Accessories
1.3.9 Distribution Wiring in a Building
1.3.10 Electrical Layout and Installation Drawings
1.3.11 Electrical Wiring in the Interior of Buildings
1.3.12 Methods of Point Wiring and Circuit Wiring
1.3.13 Feeder Wiring between SDB and BDB, DB and SDB, FDB to DB, MDB to FDB etc.
1.3.14 Conduits, Channels, Cables, Conductors and related Accessories
1.3.15 Conduits through the Building Expansion Joints
1.3.16 Types of Electrical Wiring for Exterior Lighting and other exterior purposes
1.3.17 Branch Distribution Boards, Sub-distribution Boards, Distribution Boards, FDBs and MDBs
1.3.18 Electrical Services Shafts, Bus Ducts, L.T. Riser Cables and L.T. Busbar Trunking
1.3.19 L. T. Main Incoming Cable and Service Connection
1.3.20 Design for Electrical Wiring
1.3.21 Temporary Electrical Connection for a Building Construction Site
1.3.22 Temporary Electrical Connection for an outdoor concert
Chapter 2: Air-conditioning, Heating and Ventilation
2.1 GENERAL
2.2 Scope
2.3 Application
2.4 Terminology
2.5 General Provisions
2.6 PLANNING
2.7 Air-Conditioning SYSTEM DESIGN
2.8 AIR DISTRIBUTION SYSTEM
2.9 Air-Conditioning Equipment
2.10 Refrigerating Equipment
2.11 Ventilation Systems
2.12 ENERGY CONSERVATION
2.13 Inspection, Testing and Commissioning
2.14 Operation and Maintenance
Chapter 3: Acoustics and Noise Control
3.1 Purpose and Scope
3.2 GENERAL PROVISIONS
3.3 Terminology
3.4 Zoning
3.5 NOISE PROHIBITIONS
3.6 Equipment management
3.7 Transportation
3.8 OUTDOOR NOISE
3.9 ACOUSTICS AND INDOOR NOISE
3.10 Construction Activities
3.11 SPECIFICS FOR OCCUPANCY A: Assembly
3.12 SPECIFICS FOR OCCUPANCY B: Business and Mercantile Buildings
3.13 SPECIFICS FOR OCCUPANCY E: Educational Occupancies
3.14 SPECIFICS FOR OCCUPANCY F: Factory and Industrial Occupancies
3.15 SPECIFICS FOR OCCUPANCY I4: Hospital and Clinics
3.16 SPECIFICS FOR OCCUPANCY R: Residential Occupancies
3.17 ACOUSTICAL REQUIREMENTS FOR SPECIAL OCCUPANCIES
Chapter 4: Lifts, Escalators and Moving Walks
4.1 GENERAL
4.2 ESSENTIAL REQUIREMENTS FOR LIFTS
4.3 DESIGN CONSIDERATIONS
4.4 ESCALATORS
4.5 MOVING WALKS
4.6 INSPECTION AND CERTIFICATION
4.7 OPERATION AND MAINTENANCE
Chapter 5: Water Supply
5.1 PURPOSE AND SCOPE
5.2 TERMINOLOGY
5.3 PERMIT FOR WATER CONNECTION
5.4 LICENSING /REGISTRATION OF PLUMBERS
5.5 WATER SUPPLY REQUIREMENTS
5.6 ESTIMATION OF DEMAND LOAD
5.7 WATER SOURCES AND QUALITY
5.8 WATER SUPPLY SYSTEM
5.9 STORAGE OF WATER
5.10 DESIGN OF DISTRIBUTION SYSTEM
5.11 WATER DISTRIBUTION IN TALL BUILDINGS
5.12 HOT WATER SUPPLY INSTALLATION
5.13 MATERIALS, FITTINGS & APPLIANCES
5.14 GENERAL REQUIREMENT FOR PIPE WORK
5.15 SAFE CONVEYANCE AND DISTRIBUTION OF WATER & PREVENTION OF BACKFLOW
5.16 LAYING OF PIPES ON SITE
5.17 HANGERS AND SUPPORT
5.18 PROTECTION OF POTABLE WATER SUPPLY
5.19 HEALTH CARE WATER SUPPLY
5.20 CLEANING AND DISINFECTING THE SYSTEM
5.21 INSPECTION, TESTING AND COMPLETION CERTIFICATE
5.22 GUIDE TO MAINTENANCE
5.23 INDIVIDUAL WATER SUPPLY SYSTEM
Chapter 6: Sanitary Drainage
6.1 PURPOSE
6.2 SCOPE
6.3 TERMINOLOGY
6.4 DRAINAGE AND SANITATION PLANS
6.5 LICENSING OF PLUMBER
6.6 DRAINAGE AND SANITATION REQUIREMENT
6.7 MATERIALS AND APPLIANCES
6.8 HANGERS AND SUPPORT AND PIPE JOINTING
6.9 DESIGN CONSIDERATIONS
6.10 DESIGN OF DRAINAGE AND SANITATION SYSTEM
6.11 CONSTRUCTION RELATING TO CONVEYANCE OF SANITARY WASTES
6.12 REFUSE CHUTE SYSTEM
6.13 BASEMENT FLOOR DRAINAGE SYSTEM
6.14 Health care drainage system
6.15 INSPECTION, TESTING AND COMPLETION CERTIFICATE
6.16 GUIDE TO MAINTENANCE
Chapter 7: Rainwater Management
7.1 PURPOSE
7.2 SCOPE
7.3 TERMINOLOGY
7.4 Rainwater Harvesting Requirements
7.5 Rainwater Harvesting Plans
7.6 LICENSING OF PLUMBER
7.7 Rain-water Harvesting
7.8 Roof top rain-water harvesting
7.9 Artificial ground water recharge
7.10 DRAINAGE AND SANITATION REQUIREMENT
7.11 MATERIALS AND APPLIANCES
7.12 Construction of Rainwater Storage Tank
7.13 Installation and construction of Rainwater Harvesting and Drainage System
7.14 Hangers and Support
7.15 Pipe Joints
7.16 Protection Against Rodent
7.17 Gradient of Pipes
7.18 Inspection chambers and manholes
7.19 Bedding and Backfilling
7.20 Design of Rainwater or storm water Drainage Piping
7.21 Sizing and finding number of Rainwater Drainage Piping
7.22 INSPECTION, TESTING AND COMPLETION CERTIFICATE
7.23 GUIDE TO MAINTENANCE
Chapter 8: Fuel Gas Supply
8.1 GENERAL
8.2 GAS PIPING INSTALLATION
8.3 USE OF LIQUEFIED PETROLEUM GAS (LPG)
8.4 LPG Bulk Storage Installations
8.5 INSTALLATION OF SPECIFIC APPLIANCES
8.6 List of Codes and Standards
